CARTER VR-ONE MALOSSI REED VALVE FOR VESPA 80 - 125 - 150 5718382

VR-ONE REED VALVE

TheVR-OneIt's for power purists, for those who want to push their Vespa to the limit, but not only. It has the same mounting characteristics in the body of theV-OneAnd the same cylinder housing possibilities thanks to the revised fluid dynamics of the crank chamber, the drilling of the studs and the same accessories supplied with theV-One(except for the mixer pin).
This crankcase has been designed to withstand higher powers and for this reason it is supplied with main ball bearings on the flywheel side Ø25xØ52x15 and transmission side Ø25xØ62x12, which eliminate the needle bearings and allow for greater capacity to withstand radial loads and additional resistance to axial loads, not contemplated with the original roller bearings. Dedicated oil seals are also supplied.
The greater resistance to stress due to the crank mechanism makes the crankcase perfect for assembly with our single-ring MHR cylinders, item 3117163 (stroke 57), but above all with the kit 3117361 (stroke 60). The natural combination for this configuration is with the Malossi crankshaft with full shoulders, stroke 60, supplied with the right balance and perfect for the reed valve supply foreseen for the newVR-One.

Reed valve power supply

This is where the major innovation and sporty orientation of the crankcase lies, now powered by a system SUPPLIED ENTIRELY with the reed valve assembly which, thanks also to the new high-quality carbon fibre reeds, guarantees an increase in power across all operating speeds and at the same time allows the highest speeds to be reached.
The assembly consists of a die-cast valve seat, coupled to the crankcase surface with a seal guaranteed by a special gasket, and a completely new reed valve equipped with a multiple-profile diffuser, specially designed with fluid dynamic simulation programs and featuring a particular shape of the side walls capable of both eliminating part of the turbulence, which is normally created when the air-petrol mixture passes through the diffusers, and at the same time directing the charge in the correct direction, once the reeds are opened.

The fuel manifold, designed according to the X360 technique used in our competitions, is made up of a die-cast flange connected to a Viton union by tightening a profiled lip, which guarantees a perfect hermetic seal, and at the same time allows the union to be turned in the direction desired by the user so as to perfectly orient the system according to the shape of the vehicle.

The sleeve has a 30mm inlet diameter. The ideal match is the Dell’Orto PHBH 30 carburetor (not supplied).

Malossi has decided to make a break with the past to create an iconic component for an equally iconic vehicle such as the Vespa PX 80/125/150! Making the most of all the technology and knowledge acquired along the roads and tracks of the whole world, Malossi has developed the new crankcasesV-OneAndVR-One. The design, study, research and production of these crankcases are the way in which Malossi intends to pay homage to the enthusiasts of these vehicles. The two models give the opportunity to preparers, restorers and, more generally, to all owners of a Vespa PX 80/125/150 to indulge yourself and choose the modification path that best suits your needs:

• The amateur, the restorer, the traveler and the simple Sunday tourist, looking for a component that can be perfectly replaced with the original, which does not require any modification to the vehicle and offers the maximum choice of components, from the original to the main items on the market, will have the crankcase at their disposal.V-One SPORT
• The tuner looking for maximum performance, the best internal fluid dynamics and the greatest possibility of engine development can purchase the crankcaseVR-One MHR

TECHNICAL FEATURES

Made entirely in ITALY

The technical and technological advancement of Malossi is the greatest strength of our products, the reason why we are convinced that we have created one of the best crankcases ever produced.

Strengths

In every square millimeter of the crankcase, an innovative thrust is perceptible that is evident even to the most inexperienced of tuners. The gravity shell casting, which differentiates these crankcases from the original models obtained, instead, with a die-casting process, combined with the use of modern shell moulding cores, allows for better internal shapes and made with maximum precision.
Gravity casting has allowed us to strategically increase the sections in the most stressed areas and to subject the crankcases to a post-casting tempering treatment, thus obtaining very high mechanical resistance. These products are made with a very high quality light aluminum alloy Al Si 7 Mg (EN AB and AC 42000) containing the right quantities of: Silicon, to increase mechanical resistance, Manganese, for better resilience and corrosion resistance, Copper and Magnesium, to improve workability.
The crankcase machining is performed entirely in our workshop with CAD/CAM process and carried out inside high-precision CNC work centers. All the support and closing surfaces have been machined with diamond tools capable of guaranteeing extremely low surface roughness values and practically perfect couplings.

Advantages

Both crankcases share a series of basic features such as, for example, the front arm reinforced with stress-relief ribs and sections with a calculated profile to allow the correct flow and channelling of stresses and guarantee better resistance.

Both models include brake shoe pins, which are installed directly in the company using presses capable of applying the forces necessary to create the couplings required by our designers.

In addition to the brake shoes, the crankcases are supplied with the M7 studs required for fitting the gear selector.

Finally, no version excludes the original electric starter, whose actuator can be mounted in the appropriate plane obtained in the volute.

Fitting the crankcase to the vehicle does not require the purchase of any additional components, in fact both versions are equipped with both front Silent Blocks in the arm connecting to the body and a rear anti-vibration mount connecting to the shock absorber.

Fluid dynamics has finally been implemented! Having equipped our series models with transfer bags that are adequately profiled and sized to perfectly match our Ø 63 cylinders, without excluding the possibility of mounting other thermal groups and indeed offering an increase in performance even with the latter, exempts tuners from the obligation to work on the crankcases to mount higher-performance cylinders. The M7 stud bolts for mounting the cylinders are also included in the package!

Thanks to the interventions listed, achieving greater power is no longer a problem. Even the usual inconvenience of oil leakage from the crankcase has been solved thanks to:

1. Increased pump casing walls, which also further contributes to the mechanical resistance of the casing
2. Using M8 stud bolts instead of the original M7 ones
3. Extremely high precision machining of the closing surfaces. We have eliminated the crankcase gasket, which deteriorated and was the main cause of oil leaks. Now the crankcases are perfectly coupled and closed with gasket paste, resistant even to the highest operating temperatures!

We didn't want to stop there! After assembling and disassembling original crankcases for years, working on them and trying out thousands and thousands of solutions to propose constantly updated components, we came face to face with inefficiencies and inconveniences that we analyzed to propose our solutions: this is the case of the crankcase tightening system, which in the original components is made with the classic screw-nut system, notoriously uncomfortable and not very user-friendly for the user.
Such a valuable vehicle deserves the best possible maintenance and this involves the need to assemble and disassemble the various components to replace them or even just to check their correct functioning, overhauling them when necessary. Anyone who has touched the original crankcases without disconnecting the block from the vehicle has certainly encountered the difficulty of manipulating the components that make up the block due to the awkward and difficult to reach position of the nuts, which, once unscrewed, risk falling to the ground and getting lost who knows where. Our solution is as simple as it is sophisticated: eliminate the nuts!
By making the threads in the left crankcase (or transmission crankcase) and the seats in the right side (or ignition crankcase) we have eliminated the need for nuts to tighten the two components. To prevent the screw from being accidentally knocked or damaged during operation, with the risk of ruining the thread, where possible we have made seats on the right side that allow the screws to be fully recessed, thus protecting them from any danger.

COMPATIBLE BRANDS AND MODELS